waterproof 0 10v dimmable constant voltage 150w 12v 24v 36v 48v led power supply strip light driver
Smartspower's new upgraded 0 10v dimmable led power supply 150W has a constant voltage working mode and a working efficiency of up to 92%. Aluminum housing design, good heat dissipation. Suitable for outdoor humid space lighting project installation.
Specification
| Model | SMT-12150-VD-A | SMT-24150-VD-A | SMT-36150-VD-A | SMT-48150-VD-A | |
| Certificate | UL / cUL / FCC / Class P | ||||
| Output | DC Voltage | 12V | 24V | 36V | 48V |
| Voltage Tolerance | ±4% | ±2.5% | ±1.38% | ±1.25% | |
| Voltage Regulation | ≤0.5% | ≤0.5% | ≤0.5% | ≤0.5% | |
| Load Regulation | ≤2% | ≤1% | ≤1% | ≤1% | |
| Rated current | 12.5A | 6.25A | 4.17A | 3.13A | |
| Rated power | 150W | ||||
| Voltage Ripple | 250mVp-p | 250mVp-p | 250mVp-p | 250mVp-p | |
| Overshoot voltage | <5%(full load) | <10%(full load) | <10%(full load) | <10%(full load) | |
| Output mode selection | When the black wire and the white gray wire at the output terminal are short-circuited, it indicates the Pulse-Width Modulation (PWM) mode. When they are disconnected, it indicates the Voltage Regulation (VR) mode of direct current voltage modulation. | ||||
| Switching the output mode requires the power to be cut off for 3 seconds and then powered on again for the mode switching to take effect. | |||||
| Input | Voltage Range | 120-277VAC | |||
| Frequency Range | 47 - 63Hz | ||||
| Power Factor (Typ.) @ full load |
>0.98@120VAC >0.96@277VAC |
>0.98@120VAC >0.96@277VAC |
>0.98@120VAC >0.96@277VAC |
>0.98@120VAC >0.96@277VAC |
|
| THD(Typ. ) @ full load | <15%@120V <15%@277V | ||||
| Efficiency(Typ.) @ full load |
≥86%@120VAC ≥89.5%@277VAC |
≥88.5%@120VAC ≥91.5%@277VAC |
≥88.5%@120VAC ≥92%@277VAC |
≥88.5%@120VAC ≥91%@277VAC |
|
| AC Current (Max.) | ≤1.7A @120VAC ≤0.68A@277VAC | ||||
| Standby power | ≤0.5W | ||||
| Inrush Current (Typ.) | 68A 208us@50%Ipeak 120VAC 100A 452us@50%Ipeak 277VAC | ||||
| Leakage current | <0.5mA | ||||
| Protection | Short Circuit | Hiccup mode, can be automatically restored after abnormal removal | |||
| Over Load | ≥120%,Constant - Current Mode, automatic recovery after exception | ||||
| Over temperature | When the shell temperature reaches 100℃±10℃, the power supply shut down the output, the temperature drop can be automatically restored | ||||
| Environment | Working TEMP. | -40~+60℃ (see below derating curve) | |||
| Working Humidity | 20 - 95%RH non-condensing | ||||
| Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | ||||
| TEMP.coefficient | ±0.03%/℃(0 - 50℃) | ||||
| Vibration | 10 ~ 500Hz, 5G 12 minutes/cycle, X Y Z axis 72 minutes each | ||||
| Safety & EMC | Safety standards | UL8750 CAN/CSA-C22.2 No.250.13 | |||
| Withstand voltage | I/P-O/P:1.88KVac;I/P-FG::1.88KVac;O/P-FG:0.5KVac | ||||
| Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70% RH | ||||
| Surge Immunity Test | AC Power Line:Differential Mode 2KV,Common Mode 4KV | ||||
| EMC Immunity | FCC/ICES do not request this test | ||||
| EMC Emission | FCC Part15 Subpart B;ANSI C63.4:2017;ICES-005 Issue 5 | ||||
| Others | Net Weight | 0.83KG | |||
| Dimension | 200*78*25.1mm(L*W*H) | ||||
| Packing | 10 pcs / CTN | ||||
| Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input, rated load and 25℃of ambient temperature. | ||||
| 2. Tolerance: includes set up tolerance and load regulation . | |||||
| 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. | |||||
| 4. Default states: The output mode is VR output by default. The dimming curve is a gamma2.2 curve. | |||||
| 5. Regarding LED driver load types where the driver meets the harmonic emissions requirements of ANSI C82.77-10. | |||||
|
|
 |
 |
 |
Mechanical Specification
| American wire gauge | |
| DT61 | |
| Input wire | Black(L) White(N) Green(G) Clamp on the shell (3*18AWG) |
| Output wire | Red(V+) Black(V-) (2*16AWG) (12V&24V Version) |
| Red(V+) Black(V-) (2*18AWG) (36V&48V Version) | |
| Function switching wire | Blue&White and Yellow&Gray (2*18AWG) |
| Dimming wire | Purple(D+) Pink(D-) (2*18AWG) |
| Remarks:Please make sure your connect these correctly otherwise your product will not function correctly and could be damaged | |
MCB recommendation：
| When the input voltage is 120Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 3 |
| 13A | 4 | |
| 16A | 6 | |
| 20A | 7 | |
| 25A | 9 | |
| When the input voltage is 277Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 9 |
| 13A | 11 | |
| 16A | 14 | |
| 20A | 18 | |
| 25A | 22 | |
Note：
1. The above quantities of the led drivers connected on the Type C is recommended base on the maximum ambient temperature is 50 ℃.
2. The breaker should be selected according to the input rated voltage, input rated current, ambient temperature, and trip characteristic
curve.
Dimming Operation
Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming
Related Products
|
100-277VAC universal input voltage range 150W 0 10v dimmable LED driver integrated with junction box. Metal housing design, good heat dissipation performance, UL certification, in compliance with global safety lighting regulations, 7-year warranty
Model: SMT-012-150VDH Input Voltage: 100-277vac
Dimming Mode: 0 10v dimmable
|
