best 0 10V dimming constant voltage 80w 24v 48v led power supply driver for led strip lights
New upgraded 80W 0 10V dimmable led power supply with full plastic protective shell, suitable for installation in small indoor spaces, dimming range is 0-100% ultra-deep dimming. Comply with global safety lighting regulations. 7-year warranty
Specification
| Model | SMT-24080-VD-P | SMT-48080-VD-P | |
| Certificate | UL / cUL / FCC / Class P / Class 2/SELV/RoHS | ||
| Output | DC Voltage | 24V | 48V |
| Voltage Tolerance | ±4% | ±2% | |
| Voltage Regulation | ≤1% | ≤0.5% | |
| Load Regulation | ≤1% | ≤1% | |
| Rated current | 3.33A | 1.67A | |
| Rated power | 80W | ||
| Voltage Ripple | 296mVp-p | 176mVp-p | |
| Overshoot voltage | <3% (full load) <4%(no load) | ||
| Output volt Adjustment | 24-26V | 48-50V | |
| Output mode selection | The DIP switch in the "ON" position represents the PWM (Pulse - Width Modulation) mode, and in the "1" position represents the VR (Modulation of DC Voltage) mode. | ||
| Switching the output mode requires the power to be cut off for 3 seconds and then powered on again for the mode switching to take effect. | |||
| Input | Voltage Range | 100-277VAC | |
| Frequency Range | 47 - 63Hz | ||
| Power Factor (Typ.) @ full load |
>0.98@120VAC >0.96@277VAC |
>0.98@120VAC >0.96@277VAC |
|
| THD(Typ. ) @ full load | <15%@120V <15%@277V | ||
| Efficiency(Typ.) @ full load |
≥88.0%@120VAC ≥91.5%@277VAC |
≥87.2%@120VAC ≥90.6%@277VAC |
|
| AC Current (Max.) | ≤0.83A @120VAC ≤0.38A@277VAC | ||
| Standby power | ≤0.5W | ||
| Inrush Current (Typ.) | 51A@50%Ipeak 208us @120VAC,118A@50%Ipeak 452us @277VAC. | ||
| Leakage current | <0.5mA | ||
| Protection | Short Circuit | Hiccup mode, can be automatically restored after abnormal removal | |
| Over Load | ≥120%,Constant - Current Mode, automatic recovery after exception | ||
| Over temperature | When the ambient temperature exceeds 55℃ ±5℃, the output is turned off | ||
| Environment | Working TEMP. | -40~+40℃ (see below derating curve) | |
| Working Humidity | 20 - 90%RH non-condensing | ||
| Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | ||
| TEMP.coefficient | ±0.03%/℃(0 - 50℃) | ||
| Vibration | 10 ~ 500Hz, 2G 12 minutes/cycle, X Y Z axis 72 minutes each | ||
| Safety & EMC | Safety standards | UL8750 CAN/CSA-C22.2 No.250.13 | |
| Withstand voltage | I/P-O/P:1.88KVAC | ||
| Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70% RH | ||
| Surge Immunity Test | AC Power Line:Differential Mode 2KV | ||
| EMC Immunity | FCC/ICES do not request this test | ||
| EMC Emission | FCC Part15 Subpart B;ANSI C63.4:2017;ICES-005 Issue 5 | ||
| Others | Net Weight | 0.36KG | |
| Dimension | 178*61.1*24mm(L*W*H) | ||
| Packing | 290*215*140mm 20 pcs / CTN | ||
| Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input, rated load and 25℃of ambient temperature. | ||
| 2. Tolerance: includes set up tolerance and load regulation . | |||
| 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. | |||
| 4. Default states: The output mode is PWM output by default. The dimming curve is a gamma2.2 curve. | |||
| 5. Regarding LED driver load types where the driver meets the harmonic emissions requirements of ANSI C82.77-10. | |||
|
|
 |
 |
 |
Mechanical Specification
| American wire gauge | |
| SD8 | |
| Input wire | DG128-3P |
| Output wire | DG128-2P |
| Dimming wire | DG128-2P |
MCB recommendation：
| When the input voltage is 120Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 9 |
| 13A | 12 | |
| 16A | 14 | |
| 20A | 18 | |
| 25A | 23 | |
| When the input voltage is 277Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 21 |
| 13A | 27 | |
| 16A | 33 | |
| 20A | 42 | |
| 25A | 52 | |
Warm tips:
1. Recommended Max. Carrying Current (A) = wire diameter(mm²) x 10A/mm ²
For example: 1mm ² output cable, Recommended Max. Carrying Current (A) = 1mm ² x 10A/mm ²=10A
2. Any other requests for cable, we can customized.
Dimming Operation
Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming
Related Products
|
100-277vac UL certified 80W constant voltage 0 10v dimmable led power supply. Designed with junction box and driver integrated into one. Metal shell design, good heat dissipation, suitable for indoor smart led lighting project installation.
Model: SMT-012-080VDH Input Voltage: 100-277vac
Dimming Mode: 0 10v dimmable
|
