non dimmable 700ma 10w constant current led driver strip light power supply

Top-quality led power supply 12volt for LED lighting projects. Use with LED strip lights, G4, MR11, MR16 LED bulbs and other LED installations.

         Specification                                    model SMT-012-150VTD SMT-024-150VTD Output DC Voltage 12V 24V Voltage Accuracy ±0.5V Rated current 12.5A 6.25A Voltage Regulation ±0.5% Load Regulation ±2 % ±1 % Rated power 150W 150W Input Voltage Range 100~277V AC Frequency Range 47～63HZ THD(Typ.) @full load <20% Power Factor ( Typ.） 0.98@120VAC  0.95@277VAC 0.97@120VAC  0.94@277VAC Full Load Efficiency(Typ.) 85%@120VAC   86%@277VAC 85%@120VAC   87%@277VAC AC Current（Typ.） 1.8A/110VAC Inrush Current（Typ.） 15A, 50%, 1.4ms @120VAC;   30A, 50% 1.4ms @277VAC Leakage current <0.5mA Protection Short Circuit shut down o/p voltage, re-power on to recover afterfault condition removed Over temperature 100℃±10℃ shut down o/p voltage,automatically recover after cooling.   Over Loading ≤120% constant current limiting, auto-recovery Environment Working TEMP. -40～+60℃ Working Humidity 20～90%RH,non-condensing Storage TEM.,Humidity -40～+80℃，10～95%RH TEMP.coefficient ±0.03%/℃（0～50℃） Vibration 10～500Hz，2G 10min./1 cycle，period for60min. each along X,Y,Z  axes Safety&EMC Safety standards UL8750 , CAN/CSA-C22.2 No.250.13   Withstand voltage I/P-O/P:1.88KVac  Isolation resistance I/P-O/P:100MΩ/500VDC/25℃/70%RH  EMC EMISSION FCC 47 CFR Part 15 ,Subpart B  Others NetWeight 1.5Kg Size 256*78*47mm(L*W*H) packing 340*280*185mm    10pcs /CTN    Notes 1. All parameters NOT specially mentioned are measured at120VAC input , rated load and 25℃of ambient temperature. 2. Tolerance: includes set up tolerance, line regulation and load regulation . 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. ■ Mechanical Specification:   ü Input cable 3*18AWG,the green cable to (FG) "Black" to L ,and "White" to N of Mains AC ü Output cable 2*16AWG,Red" (+) to LED Positive side (+) , "Black"(-)  to LED Negative side (-). noted that 12V 200W is with 2 group of  2*16AWG output wires to separate the output current.) ü Dimming cable 2*18AWG,DIM (+) Purple  to 0/1-10V dimmer signal(+ ),DIM (-) Grey to 0/1-10V dimmer signal (-) ü Please DO NOT connect “DIM-“ to “LED-“, “DIM+” to “ LED+” ,or other incorrect connection. ü Please make sure your connect these correctly otherwise your product will not function correctly and could be damaged.   Ø Derating Curve    ü Load carried in accordance with the load derating curve, according to the ambient temperature derating, in order to extend the running life.         Ø Dimming Operation and Connecting Diagram    窗体顶端 ü Using two ways of dimming at the same time, you must be assured that LED lighting is up to the max. Brightness then you could operate with the other dimming;   u Using one dimming ---TRIAC/Phase cut dimming 1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection a phase /Triac dimmer of lighting system. 2. Working with forward phase /leading edge ,MLV and Reverse phase /trailing edge ,ELV,TRIAC dimmers  3. Min loading is about 10% 4. Please try to use dimmers with power at least 1.5 times as the output power of the driver.           Ø Instruction: l This driver should be installed by qualified and professional person; l Please make sure the driver is installed with adequate ventilation around it to allow for heat dissipation. l Ensure that wiring is correct before test in order to avoid light and power supply damage; l If the LED drivers do not work normally, pl. don’t maintain privately, but contact us: sales1@smartselectronics.com  Or take a phonecall: 0086-595-22863721 ext.808    Official website: www.smarts-electronics.com   &   www.swinpower.com     Compatible Dimmer Type   SMARTS's UL Triac Dimmable LED Driver have been tested for compatibility dozens of brands dimmer.such as LEVITON/LEGRAND/LUTRON dimmer   Related Products   24v dimmable led driver 96W are UL CE ROHS approval.it is widely used in various industries, such as:INdoor LED illuminating lights,LED Neon,LED City Decoration,LED Lighting Advertising,LED Display,Safety Protection Apparatus....... Mode：SMT-024-096VTHW intput voltage：100~277V AC Efficiency > 82% Size：230*70*46mm   （L*W*H） Weight：1.1Kg/pcs 

24v 100w triac dimmable led driver follow the global lighting safety regulations.Passed high,low temperature and waterproof testing.Suitable for multiple application lighting projects, can be matched with a variety of brand lamp types such as AQ Lighting's LED tape and TCPi's MR16 led.

Driver pwm led is Smarts Electronic's highly acclaimed product number with phase cut and PWM inout function led power supply.The power supply's power factor can up to 0.95 and got cUL/UL/rohs/FCC/ROHS approval. And it can work with superbrightleds company's 24V light strip.

The dimming function for 150w led driver 12v is smooth, all are compatiable with all Triac/Phase-Cut/MLV/ELV dimmers or DC0-10V,Resistor & 10V PWM signal dimmers. Also pairable with Lutron, Leviton DH15S-1BZ, clcepsal、DALITEK、HDL、ABB control system etc.

This 60W constant current 0-10V dimmable LED driver features an NFC smart programming module. Output current can be adjusted via the NFC app. It offers multiple protections for short circuit, overtemperature, overload, and overvoltage. It's ideal for outdoor LED lighting projects in confined spaces.